MP Birla Advance Cement

Cement is the binder in plaster, brickwork and blockwork mortar, RCC slabs, beams, columns and footings, and the base course under flooring. The same 50 kg bag does all of it in a Kanpur house — only the mix ratio and the grade change. It is not a finish and not a waterproofer: cement plaster still needs putty or paint over it, and a leaking roof or damp wall needs a proper waterproofing system, not a richer cement mix.

Wet the brickwork the evening before and again in the morning — dry brick pulls water out of the mortar and the plaster cracks in a week. Fix level dots, then batch with a farma (gauge box), not by spade count: one 50 kg bag fills roughly 1.25 cft, so one box of cement to six boxes of sand gives a true 1:6. Mix only what you will use in 30 minutes, lay 12 mm in one pass on internal walls, level with the aluminium patti between the dots, and finish with the thapi. Never add water to mortar that has started to stiffen — re-tempered mortar loses strength permanently. Start wet curing the next morning and keep the surface damp for seven days; IS 456 requires not less than 10 days in dry hot weather, which is most of April to June in Kanpur.

• Farma (gauge box) for batchingout of stock
• Karni (mason's trowel)out of stock
• Thapi (wooden float)out of stock
• Aluminium patti (6 ft straight edge)out of stock
• Ghamela / tasla (steel pan)out of stock
• Phawda (mixing spade)out of stock
• Sand sieve (chalni)out of stock
• Spirit level, plumb bob and dori setout of stock
• Curing hose or pressure sprayerout of stock
• Plumb bob, spirit level and dori setout of stock
• Needle vibratorout of stock
• Tamping rod / plate compactorout of stock

• Fine sand (plaster grade)out of stock
• Integral waterproofing compound (Dr Fixit Pidiproof LW+ or equivalent)out of stock
• Gunny bags / hessian cloth for curingout of stock
• Chicken mesh (GI jaali) for junction stripsout of stock
• Red clay bricksout of stock
• Fine sand for the mortarout of stock
• 20mm gitti (coarse aggregate)out of stock
• 10mm gitti (coarse aggregate)out of stock
• Coarse sandout of stock
• TMT steel — quantity from your bar scheduleout of stock
• Shuttering ply and propsout of stock
• Binding wireout of stock
• Cover blocksout of stock

• Rubber glovesout of stock
• Dust maskout of stock
• Safety gogglesout of stock
• Gum bootsout of stock
• Safety helmetout of stock

• Ordering external plaster on the internal figure. Internal is 12 mm, external is 15-20 mm, so a bag drops from 150 sq ft to 125 or 95. Buy the whole house on the 150 figure and you will be 30-55 percent short on the outside face.
• Buying 53 grade for plaster because it sounds stronger. UltraTech points builders at 43 grade or PPC for plaster and masonry and keeps 53 for RCC. 53 sets fast and runs hotter, so in a thin plaster coat it gives you more shrinkage cracks, not a better wall.
• Volume-batching above M20. IS 456 clause 9.3 permits nominal mixes only for M20 and lower; M25 and above must be a design mix. A site mix called 1:1:2 is not M25 and will not test as M25.
• Cutting curing short. IS 456 clause 13.5.1 asks for at least 7 days wet curing and not less than 10 days in dry hot weather. A slab that was not cured never reaches its grade, and adding extra cement does not buy it back.
• Buying two months of cement in one lot and stacking it on the floor against a wall. Cement takes up damp and loses strength; IS 1489 clause 8 requires weather-proof storage. Stack on a wooden platform clear of walls and use bags in the order they arrived.

• Read the bag face before you accept the load. It must carry the ISI mark with the BIS licence number (CM/L-...), the IS number for the type you asked for (IS 269 for OPC, IS 1489 Part 1 for PPC, IS 455 for PSC), and the week and year of manufacture. Cement is under mandatory BIS certification, so no licence number, or a smudged or reprinted date, is a refuse.
• Weigh two or three bags at random off the truck. IS 1489 Annex B sets the average net mass at 50 kg, allows no more than 5 percent of bags to be over 2 percent light, and no single bag more than 4 percent light. A bag under 48 kg is out of spec, and across 200 bags that shortfall is a real bill.
• Buy the grade the job needs, not the grade the shop is pushing. PPC or OPC 43 for plaster, brickwork and general work; OPC 53 where you want early strength in slabs, beams and columns. PPC gains strength slower but keeps gaining, which suits masonry and plaster in a hot climate.
• Squeeze a handful from an opened bag. Fresh cement is cool, free-flowing and crushes straight to powder. Hard lumps that will not break between your fingers mean the bag has taken damp in the godown and the strength is already gone — that stock is not worth a discount.